Boating for professional and recreational purposes can be more amazing by using a high-quality stereo system. When your boat will have an upgraded stereo system with Jl marine speakers, subwoofers, and amplifiers, you will enjoy it a lot. No doubt that marine audio is of great importance, but its installation is a time-consuming process. Unlike its installation in cars and trucks, the upgrading and installation of stereo systems take much time in a boat. Do you know why marine audio installation takes a long time?
Well! In this blog, we will discuss the reasons why do marine installation process take longer.
Reasons About Time Taking Installation of JL Marine Audio
Here are a few reasons demonstrating why recreational audio systems take longer.
1- Running Wires Consumes Time
To run power wires, marine speakers, and their interconnection to boats, installers need to raise the carpet and lift the door’s slim trim panels to lay cables. This process can be even more difficult than this depending upon its application. For instance, the wires running are more complex in a sailboat as compared to others. Usually, the wire harness can run on a boat via dedicated cable channels. This addition of wiring without any accessibility is a time-consuming process. It is because of the involvement of removing storage cabinets and upholstery for correct execution in the process.
Boaters often plan to add speakers on the wakeboard tower. If you want to do the same, you should run all the cables inside a tube. And obviously, it will also take time as holes need to be drilled, then a wire fish is made to run through the tube and pulls the wire. Make sure of the reliable functionality of the system by proper paramount grommets on accessible holes. People usually like to listen to the speaker’s music at loud volume; there should be a comparatively large wire of 14 gauge. Doing so will also add complexity to the installation time.
2- Ensure Reliability Through Marine-Grade Wiring
Do you know whether marine-grade wiring is a good idea for your boat or an absolute necessity? Well! It depends upon the type of boat you have. Boats associated with high humidity levels can increase the process of corrosion. The corrosion of all your watercraft can fail the electrical connections present between JL marine audio to the battery, speaker, and amplifier.
However, you can prevent the failure of connections by taking some precautionary measures. Some such measures include connections coating with heat shrink, adhesive-lined tubing, and dielectric silicone. Because of this, installers should use even better and dedicated marine-grade wiring and cables. Many boaters prefer to use connections tinning – a thin tin coating with a single strand of copper on its top. Coating your wiring connections with this material will also take time for the prevention of corrosion. Use this time-consuming coating to make your sound system reliable for years by building protected connections.
3- Using Corrosion- Resistant and Water-Resistant Fasteners
It is very easy to install an audio system in the car and truck where an amp rack is created behind the plywood seat or in the spare tire. However, the moistness and wet conditions of the marine make the wooden boat deform and fail after swelling up. That’s why PVC and ABS plastics are used to amplify the mounting panels. Moreover, marine-graded material like High-Density PolyEthylene (HDPE) is used in its manufacturing to provide UV protection. This UV-protected boat will neither chalk nor turn fade with time.
When it comes to the addition of such accessories, it will take more time than normal. Make sure to use corrosion-resistant fasteners like stainless steel to keep those speakers workable directly in exposure to rain and water splashes. Again, these fasteners will take more time to ensure reliability and cost than zinc-coated or black oxide brethren. Due to using the time-consuming and costly fasteners, you will be able to prevent streaks and rust of hull, making it a worth-traveling boat.
4- Compliance With Ignition-Protected Devices
Whenever any electronics such as batteries share space with fuel cells, it becomes mandatory to use ignition-protected devices like ABYC E-11 (American Boat and Yacht Council) or SAEJ1171. So is the case with the boat where the battery bank shares space with the engine. In such places, battery disconnects, circuit breakers, and other electronics should have a non-combustible or non-ignited fuel mixture. One of such reliable ignition-protected devices is the Garmin radar. Such durable ignition-protected devices are more sensitive and time-demanding in installations.
Because of this, we suggest you make use of Garmin, Stinger, and T-spec. Using circuit breakers of these, your audio system will be in better compliance to perform in an even better way. Also, there are many remote controls and battery source units that are featured as having ignition-protected designs. It will take your time to figure out which electronics and battery source is more perfect for your boat. It depicts that protection of electronics from the explosion also takes some time in matching devices compatibility.
FAQs
Q: How to install the Jl audio marine?
It’s not as simple to install the Jl marine audio in a boat as it is in cars and trucks. It is because installers don’t find an ideal place to install audio systems in the boat. Given space limitations and power options, every installation offers some challenges. There may be a need for running wires and cutting panels for the components. After running wires, marine receivers are equipped with a 12-volt battery. Amplifiers, subwoofers, and Garmin marine radars can be used underneath places. Ground the connections by using electrical grounding components.
Q: What should you do to provide more protection to your gear?
To provide more protection to your gear, you should use a waterproof cover to protect the receiver of the stereo system from UV rays, sun, and water. Besides this, you can use a wired control system. Such control remotes will enable your receiver to get mounted on a protected location.
Q: Is there any wiring harnesses for your speaker or receiver?
Generally, no. Because it is impossible to predict which wiring harness will show better hooking up with your speaker or receiver. For making your boat stereo system compatible with the wiring harness, your boat should have any factory model.
Q: Which brand offers the best Marine Audio Speakers?
The best marine Audio Speakers are JL, Kicker, Sony, Kenwood, etc. But, in case you are looking for boat speakers, subwoofers, and Amplifiers, you should grab all these products from JL marine.
Final Words
To get the reliability, durability, and supreme functionality from the audio system, your boat must be equipped with professional Jl marine audio. The installation of all audio systems on the boat takes time when installed professionally. However, the marine audio installation will take more time and cost in running wirings and using water-resistant ignition-protected devices.